KAK 10.5 9X39 1:7 STAINLESS BARREL

SKU:
KAK-10.5-9X39-1-7-SS-BARREL
$150.00
(5 reviews)
Current Stock:
Adding to cart… The item has been added

KAK INDUSTRY 10.5 9X39 1:7 STAINLESS BARREL 

• Chamber- 9x39

• Length- 10.5"

• Gas system- Pistol  Length

• Gas Block Size- .750

• Threads- 5/8-24

• Finish- Matte Blasted Grey

• Twist- 1:7

• Material- 416R Stainless

• Extension- M4 Ramps

• Marked for Caliber and Twist

• Weight- 18.24 OZ

• Gas Block Dimples

• Fully Made In House From KAK Industry Produced Blanks

All Barrels Are Air Gauge Inspected for Correct Bore Size & Tolerances, completed Barrels are Inspected for Proper Headspace using Calibrated Gauging. 

DESIGNED TO BE USED WITH FACTORY WOLF 278 GRAIN SUBSONIC AMMO
***These barrels are designed to be run suppressed. Attempting to run them unsuppressed could lead to issues outside of KAK 's control in which we hold no liability.




Tags:

Reviews

  • 5
    awesome barrel !

    Posted by jw on June 30, 2020

    awesome barrel and accurate with the wolf ammo. i used this on a brs47 lower with csspecs ak pattern 9x39 magazines . i was quite supprised with the accuracy! now please get some reloading dies in stock or let customers be allowed to order them from redding direct so we can reload for this cartridge !

  • 5
    great deal

    Posted by eric on June 9, 2020

    bought bolt with 10 inch barrel and bcg put together with cheap lower after a few break in rounds works vary well subsonic ammo functioned without a problem

  • 5
    9x39 10.5" Barrel works well

    Posted by Dee on December 17, 2019

    Barrel installed without issue on my upper. This build utilized a KS47 lower, CSSPECS 9x39 AK mags and a 45 cal suppressor. In order to reliably cycle with Tula 245gr subs I needed to swap the buffer spring to a reduced force spring (-20%) and removed the internal weights from the buffer to bring the buffer weight to 1oz overall. Having done that the gun cycled flawlessly and was ~2moA at 100yds with the Tula ammo. Extremely quiet suppressed.

  • 5
    I'm very impressed with this combination!!

    Posted by Jim on October 16, 2019

    bought this in the Hope's of building a AR pistol in 9x39 . well I have to say I'm very impressed with the results.!! I first tried accuracy with the gun itself and at 50 yards I was all but putting the rounds through the same hole with the gun in a rest. I did have some short strokes at the beginning, but seemed to improve as I shot it more and more. here is where I thought things were going to get interesting. I bought a Roni 5/8 x 24 3 lug adapter. I was concerned with my accuracy going away. but surprisingly it didn't change 1 bit . then I added a silencerco Hybrid with a 3 lug attachment. After I did that I had zero issues with any functioning what so ever. it ran perfectly!! and once again accuracy or point of aim didn't shift at all!! this is by far the cheapest way to build a 9x39 gun I could find . And I'm so glad I did it !! as quick note you must use 7.62m2x39 mags for this caliber.

  • 5
    9x39 10.5 barrel

    Posted by DaBishop on February 26, 2019

    Quality barrel leaves single holes on paper. When used with the 278gr wolf ammo and a rugged obsidian with 9mm cap its a wonderfully quiet heavy hitter that stops pigs in their tracks. Works much better than the 300blk at pig stopping and reaches out much further than the .45 AR with in the heavy bullet dept, even more so than my 50 beowulf. A great barrel in a caliber that’s catching attention and gaining ground for mass appeal. I may have to retire my 300blk 8.5”